Hi
I just received my PocketGo v2 ( refreshed version from april 2020) and just to be sure I wanted to make extra SD card with system ( just in case SD card will stop working ) and have some improvements from rogue cfw
To do so I followed 2 guides and flashed 1.0.5 from this site :
https://github.com/Ninoh-FOX/POCKETGO2_ROGUE_CFW/releases/download/1.0.5/sd_image.bin
To brand new 32GB microSD
I tried to flash it using Etcher and win32 disk imagger. In both cases flashing was successful , but when turn off device, take out shipped in sd card with system , put my own sd card into TF1 slot and press power button , nothing happens. There is no light , no screen indication that something is happening.
If I put my ear to device, I can hear initial silent beep when I press power button and then low pitch sound meaning that device is "working"
Tried couple times, and there is nothing happening ( as if I try to turn on device without sd card )
If i take out battery and put the original sd , put battery back , then old ( stock ) system boots without any issues.
Is there any additional steps needed in order to flash system to my own sd card?
Would be very thankful for any hints
Guides I used:
https://www.youtube.com/watch?v=t1fBR0YjJwU
and
https://www.youtube.com/watch?v=OhR6lehQb8g
Also tried to flash 1.0 rogue and result was same ( black screen when turning on with SD card in TF1 slot )
Moving further I tried then to flash using etcher 1.0.5 , then resized ext4 partition to 28GB, put into TF1, while also having blank 32Gb FAT32 sd card in TF2, press power button for 2-3 sec ...nothing happens.
Then I moved and flashed original firmware from here https://github.com/retrogamehandheld/PocketGo2/wiki/Firmware-and-software-updates
Used etcher, flashed, resized partition to 28GB , TF1 slot, power ...nothing - black screen no logo .
I'm worried that shipped in card will eventually fail and I won't have any way to actually use the device if I can't create secondary card for it :/
I just received my PocketGo v2 ( refreshed version from april 2020) and just to be sure I wanted to make extra SD card with system ( just in case SD card will stop working ) and have some improvements from rogue cfw
To do so I followed 2 guides and flashed 1.0.5 from this site :
https://github.com/Ninoh-FOX/POCKETGO2_ROGUE_CFW/releases/download/1.0.5/sd_image.bin
To brand new 32GB microSD
I tried to flash it using Etcher and win32 disk imagger. In both cases flashing was successful , but when turn off device, take out shipped in sd card with system , put my own sd card into TF1 slot and press power button , nothing happens. There is no light , no screen indication that something is happening.
If I put my ear to device, I can hear initial silent beep when I press power button and then low pitch sound meaning that device is "working"
Tried couple times, and there is nothing happening ( as if I try to turn on device without sd card )
If i take out battery and put the original sd , put battery back , then old ( stock ) system boots without any issues.
Is there any additional steps needed in order to flash system to my own sd card?
Would be very thankful for any hints
Guides I used:
https://www.youtube.com/watch?v=t1fBR0YjJwU
and
https://www.youtube.com/watch?v=OhR6lehQb8g
Also tried to flash 1.0 rogue and result was same ( black screen when turning on with SD card in TF1 slot )
Moving further I tried then to flash using etcher 1.0.5 , then resized ext4 partition to 28GB, put into TF1, while also having blank 32Gb FAT32 sd card in TF2, press power button for 2-3 sec ...nothing happens.
Then I moved and flashed original firmware from here https://github.com/retrogamehandheld/PocketGo2/wiki/Firmware-and-software-updates
Used etcher, flashed, resized partition to 28GB , TF1 slot, power ...nothing - black screen no logo .
I'm worried that shipped in card will eventually fail and I won't have any way to actually use the device if I can't create secondary card for it :/